你好,欢迎来到GLUBET格鲁电竞_格鲁电竞预测_格鲁电竞赔率!

燃气发电机组如何加润滑油你知道吗?

   发布于:2020-02-12 10:43

GLUBET格鲁电竞_格鲁电竞预测_格鲁电竞赔率 在增压气体发生器模型的基础上增加了增压系统和心脏系统、冷却系统和独立的高温和低温循环的方法,高温循环冷却

  在增压气体发生器模型的基础上增加了增压系统和心脏系统、冷却系统和独立的高温和低温循环的方法,高温循环冷却缸,块,汽缸,如高温部件,低温循环冷却加压气体发生器,空气和油冷却器在增压气体发生器模型的基础上增加了增压系统和心脏,冷却系统采用高温循环和低温循环分开的方法,高温循环冷却气缸、缸体、缸盖等高温部件,低温循环冷却增压气体、空气和油冷却器。润滑油尤为重要,下面是对燃气发电机组充油方法的详细介绍:

  The pressurization system and heart system, cooling system and independent high and low temperature circulation method are added on the basis of the pressurization gas generator model. The high temperature circulation cooling cylinder, block, cylinder, such as high temperature parts, low temperature circulation cooling pressurization gas generator, air and oil cooler are added on the basis of the pressurization gas generator model. The cooling system adopts high temperature circulation With the method of separating from the low-temperature cycle, the high-temperature cycle cools the cylinder, cylinder block, cylinder head and other high-temperature components, and the low-temperature cycle cools the charge gas, air and oil coolers. Lubricating oil is particularly important. The following is a detailed introduction to the oil filling method of gas generator unit:

将曲轴箱注满机油,直到机油标尺上的低(L)标记。

燃气发电机组


  1. Fill the crankcase with oil until it reaches the low (L) mark on the oil scale.

  从NH/ nt-855发动机油跨通道上取下塞子,从V发动机油滤壳头部取下塞子,如图1-2、1-3、1-4、1-5、1-6所示。对于KT/ kta-1150发动机,拆卸油冷却器外壳前面的插头。注意:不要从旁路过滤器润滑发动机。

  Remove the plug from the NH / nt-855 engine oil cross passage, and remove the plug from the V engine oil filter housing head, as shown in Fig. 1-2, 1-3, 1-4, 1-5 and 1-6. For kt / kta-1150 engines, remove the plug on the front of the oil cooler housing. Note: do not lubricate the engine from the bypass filter.

  3.将手动或电动燃油喷射泵油管从清洁的润滑油源连接到外壳上的塞子凸台。

  3. Connect the manual or electric fuel injection pump oil pipe from the clean lubricating oil source to the plug boss on the housing.

  4、泵泵至低油压30磅/英寸每平方米(207 kpa)。

  4. Pump to low oil pressure 30 psi (207 kPa).

  5. 启动发动机至少15秒(关闭气阀或拆卸气路以避免启动),并在此期间将外部油压保持在15磅/英寸/m2 (103 kpa)的低水平。

  5. Start the engine for at least 15 seconds (close the air valve or remove the air circuit to avoid starting), and maintain the external oil pressure at a low level of 15 lb / in / m2 (103 kPa) during this period.

  6. 拆下外来油管并安装堵头。注:在给曲轴箱上油或加油时,应清洗溢出的油。

  6. Remove the external oil pipe and install the plug. Note: when oiling or adding oil to the crankcase, clean the overflow oil.

  7. 将第3部分中规定的机油注入曲轴箱到机油规则的高度(H)标记处。对于新的或大修过的发动机,不要改变机油的类型和粘度。

  7. Fill the crankcase with the oil specified in part 3 to the height (H) mark of the oil rule. For new or overhauled engines, do not change the type and viscosity of the oil.

  以上是燃气发电机组为大家介绍的加润滑油的方法,想要了解更多产品信息,欢迎访问网站: above is the method of adding lubricating oil for gas generator set. For more product information, please visit the website:

上一篇:用沼气发电机组检测连杆变形的方法是什么?
下一篇:沼气发电机组电磁开关坏了是怎么造成的?